186.7 vs. 89.8 gallons in the matched 8-foot configuration
The Silver Bullet difference
The six reasons this system earns the bed space.
Start with the model-specific storage gain, then evaluate the mounting system, extension, lockable protection, load ratings, and construction.
full-width across the deck and drawer floor, with four side channels per side
model-specific travel that brings stored gear to the tailgate
Weather- and dust-resistant protection with a locking compression latch
platform and drawer ratings under distributed loading
black Type II, Class 1 architectural-grade anodized finish, built for strength without steel-system weight
Exact matched comparison
The Silver Bullet Advantage
Compare exact drawer dimensions, extension, and usable in-drawer volume against a leading comparable drawer system for the bed length selected above. Changing the bed length updates this comparison.
Silver Bullet drawer advantage
60% more usable volume
157.2 gal vs. 98.3 gal. +58.9 gal (60% more)
+10.4 in
Combined drawer width
46.4 vs. 36 in total
+5.4 in
Interior length
77.4 vs. 72 in
+2.1 in
Interior height
10.1 vs. 8 in
+58.9 gal
Usable volume
60% more
+15.7 in
More drawer extension
69.7 in Silver Bullet vs. 54 in the leading system
Exact measurements used in this comparison
- Overall system length / height
- Silver Bullet: 81 in L / 12.5 in H Leading system: 75 in L / 12.2 in H
- Drawer interior
- Silver Bullet: 77.4 in L x 46.4 in W x 10.1 in HLeading system: 72 in L x 18.0 in W x 8 in H each
- Drawer layout
- Silver Bullet: one full-width drawerLeading system: Two drawers
- Combined interior drawer width
- Silver Bullet: 46.4 in across one full-width drawerLeading system: 36 in total (two drawers)+10.4 in total interior width
- Drawer extension
- Silver Bullet: 69.7 in (90% of drawer length)Leading system: 54 in+15.7 in farther reach
How to read the gains
Width compares Silver Bullet's one full-width drawer with the matched combined interior drawer width. For the 8-foot comparison, the leading system has two 18-inch drawers, 36 inches combined, each 72 inches long and 8 inches high. Length and height compare the dimensions shown. Volume compares combined in-drawer volume; the 8-foot totals apply the same length x width x height calculation to both systems. Extension compares Silver Bullet drawer travel, calculated from interior length times the model-specific extension percentage, with the leading system's published extension distance.
Silver Bullet volume is calculated from the listed interior drawer dimensions. The 8-foot comparison applies the same dimensional method to the leading system's two 72 x 18 x 8 in drawers, producing 89.8 gal combined versus Silver Bullet's 186.7 gal and a 108% gain. Other model rows use the listed source values for their matched bed class. Silver Bullet system dimensions describe the core system; included model-specific wing plates add side coverage. Percentages and dimensions are rounded. The leading system's 8-foot fitments use a standard-length drawer system with a separate load-floor extension. Review the comparison methodology and dated source record.
Third-party specifications and trademarks remain the property of their respective owners. Silver Bullet is not affiliated with or endorsed by the compared manufacturer.
Integrated mounting versatility
Built to Adapt, From Platform to Drawer
A purpose-selected HD-series profile carries mounting access across the platform deck, drawer floor, and drawer sides. The architecture scales to each truck and bed length so gear can be mounted, moved, and reconfigured without drilling permanent holes.
HD-Series 3-Inch Grid
A heavy-duty T-slot profile forms the platform's full-width 3-inch mounting grid for movable tie-downs, chocks, brackets, recovery-board mounts, and properly engineered tank mounts.
Full-Width 3-Inch Grid
The same repeating pattern supports removable dividers, tool holders, mounting plates compatible with Milwaukee PACKOUT, cargo stops, and equipment cradles inside the ultra-wide drawer.
Four Channels Per Side
Longitudinal channels keep frequently used tools, accessories, and custom brackets movable and within reach throughout the drawer.
Build your loadout
Effectively Open-Ended Mounting Positions
The same system can evolve from daily work to ranch duty, trail recovery, moto weekends, or expedition travel without rebuilding the drawer around one permanent setup.
- Mounting plates compatible with Milwaukee PACKOUT
- Properly engineered fuel or water tank mounts
- Wheel chocks and movable tie-down points
- Recovery-board and recovery-gear brackets
- Air compressors and power-system mounts
- Fire extinguishers, tool holders, and dividers
- Bike, moto, and cargo-stop hardware
- Custom brackets for changing work demands
Mounting and trademark notes
All mounts and accessories must be properly engineered, rated, secured, and installed with suitable hardware. Vehicle payload limits and Silver Bullet's distributed-load ratings still apply. Milwaukee and PACKOUT are trademarks of Milwaukee Electric Tool Corporation; Silver Bullet is not affiliated with or endorsed by Milwaukee.
Model-specific reference Full dimensions and weights
Open the reference table for every supported bed length. The selected configuration's core dimensions remain visible near the bed-length selector above.
| Configuration | Model years | Overall system | Drawer interior L x W x H | Drawer extension | Approx. weight |
|---|---|---|---|---|---|
| 6.75 ft bedSB-SD-17P-69FT-R1 | 2017-Current | 81 in L / 12.5 in H | 77.4 in L x 46.4 in W x 10.1 in H | 69.7 in (90%) | 311 lb |
| 8 ft bedSB-SD-17P-8FT-R1 | 2017-Current | 95 in L / 12.5 in H | 91.4 in L x 46.6 in W x 10.1 in H | 83.2 in (91%) | 365 lb |
Dimensions and approximate weights are configuration-specific reference values. After purchase, Silver Bullet confirms the selected vehicle configuration and reviews disclosed bed accessories before releasing the system to fabrication.
Order, build, and factory installation
A Clear Path From Configuration to Handoff
Each system is built to order for a specific truck configuration, then installed by the same Palmer Lake team that built it.
See the 5-step order and installation process
- 01Choose your configuration
Select the listed truck family and bed length that match your vehicle.
- 02Place the order
The displayed price includes model-specific wing plates and standard factory installation.
- 03Confirm vehicle details
After purchase, we confirm the selected configuration and review disclosed bed accessories before fabrication.
- 04Build and schedule
Silver Bullet builds the system, then coordinates the final Palmer Lake installation appointment.
- 05Install and hand off
We mount, align, and function-check the system, then walk through use, loading, and care.
After installation Ownership, care, and serviceability
The system is designed for demanding use, clear maintenance, and direct support from the people who build it.
Gasket-Sealed and Lockable
A locking compression latch pulls the drawer face against its perimeter gasket. The enclosure is weather-resistant and dust-resistant, not waterproof, submersible, pressure-washer proof, theft-proof, or IP rated.
Accessible, Replaceable Components
Seals, mounting points, rollers, and moving hardware can be inspected and serviced. Owner handoff includes practical care guidance.
Built in Palmer Lake, Colorado
Design, engineering, testing, manufacturing, factory installation, and support happen here at the foot of the Rocky Mountains, using U.S.-sourced aluminum and rubber.
Patent-Pending Architecture
A provisional patent covers the roller, gasket, extrusion, and related system architecture, with a broader portfolio in development.
Questions before ordering
How is my truck configuration confirmed?
2017-Current Ford Super Duty; 6.75 ft and 8 ft beds. Listed configurations are engineered from factory OEM vehicle CAD for no-drill installation. The selected vehicle configuration is confirmed and disclosed bed accessories are reviewed before production.
Is the system waterproof or theft-proof?
No. Silver Bullet is gasket-sealed, weather-resistant, dust-resistant, and lockable. It is not waterproof, submersible, pressure-washer proof, theft-proof, or IP rated.
What do the load ratings mean?
The 2,000 lb platform-deck rating and 400 lb drawer rating are both based on distributed loading. Point loading, cargo securement, driving conditions, and vehicle payload limits still apply.
Can my drawer system be shipped instead of factory installed?
Not at launch. Silver Bullet drawer systems are currently factory installed at the Silver Bullet shop in Palmer Lake, Colorado, rather than shipped to customers. Consumer shipping is planned for a later phase. Join the shipping availability list for updates. Approved dealer orders use a separate quote and fulfillment process.
What are the payment and warranty terms?
Standard checkout collects the full selected price, including standard factory installation. Eligible customers may see Shop Pay Installments during checkout. Review the complete payment, cancellation, return, and limited-warranty terms.
Unsupported truck? Request a future fitment
Help shape the fitment roadmap
Don't see your truck?
Tell us the year, make, model, and bed length. Your request helps prioritize the next Silver Bullet fitment, and we will contact you when a matching system moves toward production.
01 / Submit your truck
02 / Join the fitment waitlist
03 / Hear from us as development advances